How to adjust the machine parameter on Xhorse Dolphin XP-005


How to adjust the machine parameter on Xhorse Dolphin XP-005 auto key cutting machine? Here is the step-by-step operation guides, incl. Height level adjustment, clamp calibration and cutting calibration. Check the steps as follows.

How to adjust height level on Xhorse Dolphin XP-005?

Step 1: Enter Dolphin XP-005 operation main interface and on “Machine Parameter” 



Step 2: Select “Height Level Adjustment”



Step 3: Adjust the heights of cutter and probe by following the tips on the screen, then click on “Start”



Step 4: After the machine has stopped, adjust the points of probe and cutter to the same level by following the tips on the screen. Then click on “Continue”



Step 5: After the machine has stopped, select the diameter of the installed cutter, click on “Setting cutter diameter” for finish height level adjustment



How to calibrate clamp on Xhorse Dolphin XP-005?

Step 1: Open Dolphin XP-005 operation main interface

Select “Machine Parameter”-> “Clamp Calibration”




Step 2: Click on “M1 Clamp”

Follow the tips on the screen, put HON66 key blank, click on “Start” and wait until it is finished



Step 3: Select “M2 Clamp”

Pay attention to the tips, select the side A and do not place any key on the clamp, and then click on “Start”


Step 4: Follow the tips on the screen and change to other B, C or D sides for finish calibration



How to calibrate cutting on Xhorse Dolphin XP-005?

Step 1: Open the operation main interface and click on “Machine Parameter”



Step 2: Select “Cutting Calibration”

Operate by following the tips and click on “Start”




Step 3: Clean the cutter, probe and working area with a brush

Click on “Continue” for finish cutting calibration



That’s all. Hope it helps!

Comments

Post a Comment

Popular posts from this blog

How to update Xhorse Dolphin XP-005?

Image
How to update Xhorse Dolphin XP005 ? Here are three methods to get the update package. Method 1: Contact your distributor and ask for “Upgrade Kit” Method 2: Send an email titled “Update tool” to support@xhorse.com Method 3: Consult with online customer service on Xhorse App. Source:   Xhorse "Upgrade Kit" Download:  http://www.xhorsetool.com/info/software-download/ Steps to update both Dolphin XP-005 database and firmware with update package: Step 1: Connect the Dolphin with a computer through USB cable Run “Upgrade Kit” Click “Find Device” Step 2: The connected device will be recognized and shown on left corner. Step 3: If the device cannot be found, follow the tips on screen and click “YES” to install driver Step 4: Select DOLPHIN 1 and install driver Step 5: When the dolphin machine is found, click “Upgrade” Step 6: It takes a few minutes to complete upgrading. Please make sure the USB cable is always well connected when upgrading.
Read more

Copy BMW HU92 Key: Done by Xhorse XP-005 Plus Keytool Max

Image
How to: Copy a BMW HU92 key by Xhorse Dolphin XP005 and Key tool Max? Preparation: Dolphin XP-005 auto key cutting machine Xhorse VVDI Key Tool Max Original BMW HU92 key + Blank key Procedures: Connect Key tool max with Dolphin XP005 via Bluetooth Enter Dolphin XP005 main menu Select the corresponding car make, model and key type Follow the instruction to put the working key to the XP005 cutting machine Decode key When finish decoding, put the new key to cut both sides Finally, test the keys Source: http://blog.xhorsetool.com/dolphin-xp005-plus-key-tool-max-cut-bmw-hu92-key/
Read more

Review on Xhorse Condor Dolphin Key Cutting Machine

Here are Reviews of  Xhorse Condor dolphin key cutting machine . Bobb Keil : The Xhorse dolphin cuts high Security, standard security, and tibbe akl it will duplicate single sided. The xhorse cutting tools are designed for Automotive keys. Dm me if you have questions I have the mini and the dolphin Carlton Quay : mini has its own screen and the Xhorse dolphin runs from your phone or tablet Jason Henkle:  I've cut eight keys and I'm down to about 85% last I remember and I charged it on Tuesday when I got it. I think it was rated for more than 25 on a full charge. It weighs a decent amount and I'm still thinking of a way to bolt down. I've only had a Framon for over 12 years so this this is a luxury! Ameer Hasan:  nothing to worry about there is a tech support also its a good machine i got it couple months ago its a fantastic machine worth of money Martyn Clinton:  I got a condor and a dolphin Both are ok Condor has less glitches Both have shit names I mean
Read more