Xhorse Dolphin XP-005 Key Cutting Machine Review

Here share the operation instructions on Xhorse Dolphin XP-005 auto key cutting machine , incl. how to use key duplication, make a key by key bitting and find bitting. Let's go one by one. How to use key duplication on Xhorse Dolphin XP-005? Note: Car models and years are needed to for key duplication Step 1: Go to Dolphin XP-005 operation main interface Click on “Vehicle Database” Step 2: Select or type the car maker Step 3: Select the car model Step 4: Select the car model and year Step 5: Follow the tips on the screen and correctly put the key on the clamp Click “Decode Key” Step 6: After getting the original key bit Put a new blank key and click on “Cutting Key” How to use cut by bitting on Xhorse Dolphin XP-005? There are two ways to use the key biting to make a key: Method 1: Making a key without the original key 1.Use some special tool to get the key bitting 2.Break down the lock to read the key bitting on each metal of lock ...

How to adjust the machine parameter on Xhorse Dolphin XP-005 auto key cutting machine ? Here is the step-by-step operation guides, incl. Height level adjustment, clamp calibration and cutting calibration. Check the steps as follows. How to adjust height level on Xhorse Dolphin XP-005? Step 1: Enter Dolphin XP-005 operation main interface and on “Machine Parameter”  Step 2: Select “Height Level Adjustment” Step 3: Adjust the heights of cutter and probe by following the tips on the screen, then click on “Start” Step 4: After the machine has stopped, adjust the points of probe and cutter to the same level by following the tips on the screen. Then click on “Continue” Step 5: After the machine has stopped, select the diameter of the installed cutter, click on “Setting cutter diameter” for finish height level adjustment How to calibrate clamp on Xhorse Dolphin XP-005? Step 1: Open Dolphin XP-005 operation main interface Select “Machine Parameter”-> “Clamp Calibration” Step 2: C...

This article is available with the operation guide to use key database on Xhorse Condor Dolphin XP-005 when all keys lost. There are three ways to make keys from the key database: Method 1: Original key code card from factory Method 2: Key code information on lock for some car models Method 3: Other ways to get the key code Step-by-step guide to use key database: Step 1: Enter the Dolphin XP-005 operation main interface Click on “All Key Lost” Step 2: Select a car maker Step 3: Put in the key code circled and click “QUERY” Step 4: Select the key series Step 5: The key bit will be automatically generate on the screen And click “Cutting Key” to do key cutting operation Job’s done!

How to update Xhorse Dolphin XP005 ? Here are three methods to get the update package. Method 1: Contact your distributor and ask for “Upgrade Kit” Method 2: Send an email titled “Update tool” to support@xhorse.com Method 3: Consult with online customer service on Xhorse App. Source:   Xhorse "Upgrade Kit" Download:  http://www.xhorsetool.com/info/software-download/ Steps to update both Dolphin XP-005 database and firmware with update package: Step 1: Connect the Dolphin with a computer through USB cable Run “Upgrade Kit” Click “Find Device” Step 2: The connected device will be recognized and shown on left corner. Step 3: If the device cannot be found, follow the tips on screen and click “YES” to install driver Step 4: Select DOLPHIN 1 and install driver Step 5: When the dolphin machine is found, click “Upgrade” Step 6: It takes a few minutes to complete upgrading. Please make sure the USB cable is always well connected when upgrading....

Xhorse Dolphin XP-005 Cutter and Probe Installation and Uninstallation. Installation steps: 1)Put the cutter Into the cutter mounting hole and push the cutter to the limit. Then drop the cutter 2-5 mm down. When the screw is perpendicular to the notched part of the side of the milling cutter, the locking screw and the fixed milling cutter. 2)Push the probe into the probe mounting hole and the tip of probe need to be  higher than the tip of cutter .Turn the 'probe locking screw' clockwise until the probe is locked. Uninstallation steps: 1)Unscrew the locks for cutter and probe counter-clockwise until they are loosened off. 2)Take the cutter or probe off when it Is loose.